1997-2004 Buick Regal Window Regulator Installation Manual

Buick Regal Installation — Buick user or technician who tried to install Window Regulators do not need to be confused because udugs.com been sharing information about the installation, deletion or replacement of the vehicle types Buick Regal and Buick Century. before doing the job you should peruse the following guide. The following information along with instructions.

Window Regulator Removal

Utilizing a decide or small flat-blade screwdriver, take away the inside door trim panel retaining screw cowl plate. Utilizing a 10mm socket and ratchet assembly, remove the 2 (2) inside door pull retaining screws.

Using a trim panel removing device, remove the interior door trim panel assembly. Disconnect the facility swap assembly. Take away the interior door trim panel.

Remove the water vapor barrier. Utilizing a T-30 Torx bit and ratchet meeting, take away the Torx bit retaining the inside door trim panel support bracket.

Briefly connect the ability switch assembly and lower the door glass, exposing the screws retaining the window regulator to the door glass. Utilizing a ten mm socket and ratchet meeting, remove the 4 (4) interior door trim panel help bracket retaining screws.

Disconnect the ability switch assembly. Using a 10mm socket and ratchet assembly, remove the 2 (2) screws attaching the window regulator to the door glass.

Once the door glass has been separated from the window regulator, manually slide the door glass into the closed position and maintain in place with both a saddle cup assembly, painter’s tape, or a wedge.

Disconnect the window raise motor connector. Utilizing a 10 mm socket and ratchet assembly, take away the three (three) window carry motor retaining screws. Remove the window regulator by the principle entry hole.

Window Regulator Installation

Set up the window regulator by means of the primary entry hole. Using a ten mm socket and ratchet meeting, connect the 4 (4) window regulator/interior door trim panel support bracket retaining screws.

Utilizing a 10mm socket and ratchet assembly, attach the three (3) window carry motor attaching screws. Connect the window carry motor connector. Briefly join the power change meeting to raise or lower the window regulator, aligning the points mounting the door glass to the window regulator.

Manually slide the door glass into position to align the factors attaching the door glass to the window regulator. Utilizing a 10mm socket and ratchet assembly, connect the door glass to the window regulator.

Install the Styrofoam noise insulator. Attach the water vapor barrier. Join the facility change meeting connector. Set up the inside door trim panel assembly. note : You’ll want to align the entire interior door trim panel retainers. Failure to do so might end in damage to the inside door trim panel or the interior door trim panel retaining clips. Utilizing a 10 mm socket and ratchet assembly, attach the 2 (2) inside door pull retaining screws.

Set up the interior door pull retaining screw cowl plate.  Confirm that the interior door trim panel is secured and that the window regulator is operating properly.

it’s just short of our guidance, you might also want to know the types of equipment that will be used to begin the removal and installation on Window Regulators. The following equipment is needed.

Tools required

  1. Silicone spray lubricant
  2. Trim panel removal tool
  3. Pick
  4. Saddle cup assembly, tape, or wedge to hold window in place
  1. Flat-blade screwdriver or plastic pry tool
  2. 10mm socket or driver
  3. Phillips screwdriver
  4. Grease pencil or marker
  5. T-30 Torx bit
Summary
Review Date
Author Rating
51star 1997 2004 Buick Regal Window Regulator Installation Manual1star 1997 2004 Buick Regal Window Regulator Installation Manual1star 1997 2004 Buick Regal Window Regulator Installation Manual1star 1997 2004 Buick Regal Window Regulator Installation Manual1star 1997 2004 Buick Regal Window Regulator Installation Manual
You might also likeclose